Diameter is the measurement across the inner width of the ring

You'll need:

• A ring that fits you
• Ruler

• 
  Step 1

  Find a ring that fits.

• 
  Step 2

  Lay the ring on top of a ruler, and measure the widest area inside the ring from the inner edge to the inner edge. Round off to the closest whole millimeter.

Circumference is the measurement around the base of the finger

You'll need:

• 5mm wide strip of pager
• Pencil of fine tip pen
• Ruler

• 
  Step 1

  Cut a long strip of paper that is 5.0 mm wide.

• 
  Step 2

  Wrap the strip of paper around the base of the desired finger. For the most accurate result, pull the paper as tightly as possible.

  *Don’t worry! The correct ring size is determined on the basis of a tight measurement; the ring itself won’t fit that tightly.

• 
  Step 3

  Ensure that the paper is evenly overlapped and pulled tight, and mark where the strip of paper meets itself.

• 
  Step 4

  Measure the length of the strip of paper in millimeters. Round off to the closest whole millimeter.

If you already have a necklace whose length you like, you can measure it to help determine which size to choose. There are two ways to measure a necklace.

You'll need:

• Flexible measuring tape or ruler
• A necklace you like

Option 1

Measure Full Length

Lay the necklace down on a flat surface in a straight line. Measure it from one end of the clasp to the other and note down the length.

Option 2

Measure When Closed.

With the necklace clasp closed, lay it down on a flat surface and measure its length from end to end. Next, double that measurement and note it down.

If you don’t have a necklace to use as reference, you can use a tape measure or a piece of string to determine the perfect length.

You'll need:

• Tape measure or ruler
• String
• Pen or a marker

• 
  Option 1

  Use Flexible Tape Measure

  Place the flexible tape measure around your neck like a necklace, adjust it to the desired length, and note down the measurement.

• 
  Option 2

  Place a piece of string around your neck like a necklace, adjust it to the desired length, and mark where the string ends meet with a pen or a marker. Next, measure the string and note the length.

A choker should sit comfortably around your neck. Find your neck size by using the instructions below, then add 2-4 inches or 5-10 cm to your neck measurement, depending on the desired fit.

You'll need:

• Tape measure or ruler
• String

• 
  Option 1

  Use Flexible Tape Measure

  Place a flexible tape measure comfortably around your neck to find your neck size. Next, add 2 inches or 5 cm to your neck size to find your choker size.

• 
  Option 2

  Place a piece of string around the circumference of your neck. Mark where the string ends meet and measure the length. Next, add 2 inches or 5 cm to your neck size to find your perfect choker size.

Follow the instructions below to determine your wrist size. The general rule for finding your bracelet size is to add 2cm (0.8in) to your wrist size measurement. To ensure the most accurate bracelet size, always use the size chart for your selected bracelet type. If you prefer a looser fit, you may wish to size up.

You'll need:

• Flexible measuring tape or ruler
• String or strip of paper
• Pen or marker

Option 1

Use a flexible measuring tape

With your palm open and facing up, wrap the measuring tape around your wrist, just above your wrist bone. Note down measurement of your wrist size.

Option 2

Use a string.

With your palm open and facing up, wrap the string or strip of paper around your wrist, just above your wrist bone. Mark where the ends meet with a pen or a marker. Next, lay the string or piece of paper flat and measure it to where you've made the mark to find your wrist size and note it down.

---

Using the wrist measurement you've just found, find the chart for your preferred bracelet type to see which bracelet size corresponds with your wrist size.